Ketra Lighting in Ottawa: What It Is and How to Plan It Into Your Home
Most people who ask us about Ketra have already seen it somewhere. A kitchen where the white light looked like late afternoon sun. A painting that looked better at night than it did at noon. Then the questions start. What is it? Why does it cost more than a pot light? Will it work in my house?
Here are the answers, with specs from Lutron's own documents. If you're after light that follows the sun through the day, our circadian lighting post covers that side. This one is about the hardware and the planning.
What Ketra actually is
Ketra is a line of lights made by Lutron. It isn't a switch or a hub. It's downlights, lamps and linear fixtures, and every light source has its own wireless control built in.
A regular LED pot light uses white LEDs. Buy 3000K and you get 3000K, forever. Ketra mixes light from several coloured LEDs and white ones inside a single module. That mix is how one fixture can go from 1,400K, about the colour of a candle, all the way to 10,000K. It can also do pastels and full colour.
Because each light has its own radio, control isn't tied to the wiring. Lutron points out that the lights can be rezoned later without rewiring. Move the dining table two feet and the lights over it can become their own zone. That's a programming change, not a call to the electrician.
Ketra vs a regular dimmable LED
Here's where Ketra is different once it's in your ceiling:
- Colour rendering. Lutron rates its D2R and D3 downlights above 90 CRI, with R9 above 90, from 2700K to 5000K. R9 is the deep red score. It's the one that makes skin, wood floors and a steak look right. When an LED spec sheet doesn't list R9, ask why.
- Every light matches. Lutron's Color Lock holds each light to a one-step MacAdam ellipse across all Ketra product families, for the life of the product. In plain words, the cove light and the pot lights over the island show the same white, and they're built to keep matching as they age. Lutron says the system checks its output 360 times a second.
- Dimming. Ketra dims down to 0.1%. With Natural Dimming the light also gets warmer as it goes down, as low as 1,400K, the way an old incandescent bulb did.
- Vibrancy. Lutron calls it a third dial. It changes the recipe of the white light, the balance of red, green and blue, without changing the colour of the white itself. Turn it up and the colours in a painting get richer.
- No wall dimmer. A regular LED goes on a dimmer. Ketra never does. More on that below, because it's the biggest planning point of all.
The fixtures, and where each one fits
Lutron sorts Ketra into downlights, lamps and linear lights. This is how we use them in a house:
- New construction downlights. The D2 has a 2 inch opening and the D3 a 3 inch opening. Both come fixed, adjustable or as a wall wash. The D3 runs at 9, 13 or 18 watts, and Lutron puts it in the class of a 75 W halogen. Beams go from a tight 15° to a wide 60°.
- Remodel downlights. The D2R goes in through a finished ceiling. The D4R is a 4 inch fixed downlight that uses a Ketra S30 lamp.
- Lamps. The A20 comes with a standard E26 or GU24 base, so it fits pendants, sconces and table lamps. The S30 and S38 go in track heads and in 5 or 6 inch recessed cans. That's how a pendant or sconce you already love gets Ketra light.
- Linear. The G2 is for coves, wall washing and grazing stone, at up to 1,000 lumens per foot. The LS0 Lightbar Slim is for under cabinets and shelves, from 10 to 96 inches long. It's low voltage and runs off an X96 controller that mounts on a 4 x 4 junction box.
The trim choice drives the ceiling work. On the D3 you pick flanged, flangeless mud-in or millwork, in white, black, silver, bronze or paintable white. A mud-in trim looks great, just a clean hole in the ceiling, but it's plastered in. Lutron's D3 sheets call for a 5.5 inch cut-out for mud-in where flanged needs 4 inches. Decide before the drywallers show up.
Ketra needs HomeWorks
Lutron lists three systems Ketra works with: HomeWorks, Athena and myRoom XC. Athena is for commercial buildings and myRoom XC is for hotels. In a house, that means Lutron HomeWorks. RadioRA 3 isn't on the list. If you're still weighing the two systems, our RA3 vs HomeWorks post lays out the differences.
On a current HomeWorks QSX system, the lights talk to a Clear Connect Type X gateway. That's Lutron's wireless network for Ketra, CCX for short. The gateway runs on PoE, so one network cable gives it both data and power.
Lutron's wireless rules are strict, and we design to them:
- Every Ketra light has to be within 75 feet of its gateway or processor, and Lutron recommends keeping them on the same floor. A two-storey house with a finished basement often needs more than one gateway.
- Each light needs at least two other powered CCX devices within 25 feet. One lonely pot light at the end of a long hallway is a design problem.
- Lights stay at least 3 feet from 2.4 GHz noise like Wi-Fi access points and microwaves. The gateway gets 5 feet. We usually do the Wi-Fi as well, so both go on the same drawing.
- No gateway inside a metal enclosure, and no PoE cable run outdoors.
We do the setup in the Lutron app over Bluetooth. Stand in a room and the nearest light turns bright blue. Tap to put it in a zone, it turns green, and the app moves to the next one. When everything is assigned, the lights change from cool white to warm white to say they're ready for programming. It's oddly satisfying to watch.
The wiring rule your electrician needs to hear early
Lutron's install guide says Ketra must not be connected to or controlled by a line voltage dimmer of any kind. It also recommends against switching the power with a regular toggle switch. The spec sheets put it bluntly: these lights need continuous power, so bypass any dimmer or switch between the breaker and the light.
Here's why. A light with no power can't hear a command. Someone flips the old switch off, then presses the keypad, and nothing happens. The keypad says the scene is on. The room stays dark.
So in a Ketra room there's no switch leg. The circuit runs straight to the lights and stays live, and the wall gets a Lutron keypad instead of a switch. On HomeWorks that's usually Palladiom or Sunnata, and our Palladiom keypads post covers how to pick them. Lutron says a licensed electrician should do the line voltage wiring, and we work alongside yours on the layout.
Ottawa ceilings, attics and porches
A few things come up in Ottawa houses more than anywhere else:
- Top floor ceilings. The D2R remodel downlight is not IC rated, and Lutron says to keep it 8 inches from all ceiling insulation. Most top floor ceilings here have a deep layer of attic insulation sitting right on them. The D3 comes in an IC rated new construction housing, so on a top floor we plan D3 during the build.
- Spray foam. That D3 IC housing is rated for direct spray foam, but only up to a limit: less than R-21, or 3 inches of closed-cell foam. Tell your insulation crew before they spray.
- Covered porches. Lutron allows the D3 in enclosed or covered residential patios with a trim lens. It's rated to run down to -35°C, but Lutron doesn't guarantee colour accuracy below 0°C. For porch light in January, that's fine. Just don't expect it to match the front hall to the decimal.
Adjusting the light after you move in
You don't need a programmer every time you want the kitchen a bit warmer. In the Lutron app, a Ketra zone gives you more than a brightness slider. You get colour temperature, full colour and Vibrancy. There's even a camera tool that matches the light to an object in the room.
For bigger changes, HomeWorks QSX has Lighting Designer Mode in the app, and it works in homeowner mode too. Pick a room, pick a zone, then change the level, the colour temperature or colour, Vibrancy and fade time while the lights change in front of you. Save it to the scene, and every keypad button that calls that scene picks up the change.
One catch. Lutron says those edits are written to the processor, not to the dealer's project file. So tell us when you've made changes, and we'll sync them into our file. Otherwise a later transfer from our end could undo them.
The daily rhythm, where the light cools at midday and warms up after supper, is the Natural Show. The circadian lighting post covers it.
What drives the cost
We won't put a number in a blog post. Every house is different, and a made-up average helps nobody. These are the things that move the price:
- The number of light sources. Every Ketra downlight, lamp and linear run is its own smart device. The count matters more than the square footage.
- Trims and ceiling work. Mud-in trims mean extra drywall work around every light.
- Gateways. The 75 foot and same floor rules decide how many you need.
- Keypads and programming. The HomeWorks processor, a keypad in each room, and the time to build and tune the scenes.
- When you do it. Open joists are the easy time.
For a sense of scale, Lutron's own Ketra brochure shows an example 2,200 sq ft high-rise condo: 56 D3 downlights, 200 feet of G2 cove light, 11 A20 lamps in pendants and sconces, 19 Palladiom keypads, one HomeWorks QSX processor and one CCX gateway. That's Lutron's example, not one of our projects. It shows how fast the count adds up.
Ketra doesn't have to go everywhere. Lutron's own price markers on its linear lighting page put Ketra linear at four dollar signs. Lumaris tunable tape, 1,800K to 4,000K, gets one. Rania natural white tape, 1,800K to 5,500K, sits at three. We put Ketra where people live and where the art hangs, and use the other families or plain dimmable LED in closets and storage rooms. We keep one family per room so the whites don't fight each other.
Planning Ketra into a build or renovation
Bring these to the first meeting with your builder or designer:
- Is the house going on HomeWorks? Ketra needs it.
- Which rooms get Ketra, and which get Rania, Lumaris or regular LED?
- Where do the gateways go, and does each spot have a network cable back to a PoE switch?
- Are all the Ketra circuits wired for constant power, with no switch legs?
- Mud-in or flanged trims, and does the drywall crew know?
- Any top floor ceilings under insulation that need IC housings?
- Which decorative fixtures should get Ketra lamps?
- Where is the art going, so the adjustables and wall washers can be aimed at it?
Our pre-wiring mistakes post covers the rest of what goes in while the walls are open, and our new construction page explains how we work with builders.
Talk to us about Ketra
We're Ottawa's largest Control4 and Lutron dealer and an authorized Ketra dealer. We design, program and support Lutron HomeWorks with Ketra from Orléans to Kanata and across the river in Gatineau. Send us your drawings, even rough ones, and we'll mark up where Ketra makes sense and where it doesn't. Call us at (613) 830-6787 or send us a message. You can also drop by the showroom at 1344 Youville Drive in Orléans to talk it through.
Frequently Asked Questions
Does Ketra work with Lutron RadioRA 3?
No. Lutron lists Ketra for HomeWorks, plus Athena and myRoom XC for commercial buildings and hotels. In a home, Ketra means a HomeWorks system.
Can Ketra go on my existing dimmer?
No. Lutron says Ketra must not be connected to a line voltage dimmer and recommends against switching its power with a regular switch. The lights need constant power and are controlled by Lutron keypads, the app or a schedule.
Can Ketra be added to an existing house?
Often, yes. The D2R remodel downlight installs through a finished ceiling, and Ketra A20, S30 and S38 lamps can go in existing fixtures with the matching socket. The circuits still need constant power, and the D2R has to stay 8 inches from insulation, so top floor ceilings take more planning.
How is Ketra different from tunable white LED?
Ketra mixes several LED colours to make white from 1,400K to 10,000K, plus full colour, and Lutron rates its downlights above 90 CRI and R9 from 2700K to 5000K. Color Lock keeps every Ketra light at the same colour point. Lutron's Lumaris tunable white tape runs from 1,800K to 4,000K.
Can I change the lighting settings myself?
Yes. The Lutron app adjusts brightness, colour temperature, colour and Vibrancy on Ketra zones, and Lighting Designer Mode on HomeWorks QSX lets you save changes to a scene. Let us know so we can sync the changes into the project file.
What warranty does Ketra have?
Lutron's D3 spec sheet lists five years or 25,000 hours from the date of shipment, whichever comes first, for the light source.
