Lutron Palladiom Keypads in Ottawa: Picking Finishes, Buttons and Engraving
Walk into most Ottawa houses built in the last 30 years and you'll find it by the front door. Four, five, sometimes six switches in a row. Nobody remembers which one does the porch light. Guests flip three of them before they find the hallway.
A good keypad fixes that. One plate, a few buttons, each one labelled in plain words. Lutron's Palladiom is the keypad we reach for when the controls have to look as good as the rest of the room. Here's what goes into picking one, from the finish to the words on the buttons.
What a Palladiom keypad is
Palladiom is Lutron's architectural keypad. The faceplate and the buttons are made from the same material, so it reads as one flat, clean piece on the wall. The faceplate snaps on with no screws showing. The engraving on each button is backlit in white, so you can read it in a dark hallway at 6 AM in January.
It's a wired, low voltage keypad. It talks to a Lutron HomeWorks processor over a cable Lutron calls the QS link. It doesn't carry power to your lights. It sends a command and the system does the rest, which is how one small plate can run a dozen lights and the shades at once.
One spec matters here. Lutron rates it for indoor use between 0 and 40°C. An unheated Ottawa garage or a three-season porch is the wrong spot. Put it just inside the heated door instead.
Does it work with RadioRA 3, or only HomeWorks?
We get this one a lot, so here's the answer from Lutron's own documents. Lutron lists the Palladiom keypad for HomeWorks, and its spec sheet says the keypad is wired to a HomeWorks processor on the QS link. Lutron's RadioRA 3 product guide lists Sunnata and seeTouch keypads. Palladiom keypads aren't on it.
So if Palladiom is a must, you're looking at HomeWorks. On RadioRA 3, the Sunnata keypad is the choice. It's wireless and needs a neutral wire, so it usually fits an existing wall box with no new cable. HomeWorks can use Sunnata too, so a HomeWorks house can mix them: Palladiom in the main rooms, Sunnata in the laundry room and the basement.
Our RA3 vs HomeWorks post goes through the bigger differences between the two systems.
Picking the finish
Palladiom has a long finish list. By our count from Lutron's spec sheet there are 22, in four groups:
- Architectural matte (10). White, Ivory, Light Almond, Almond, Beige, Taupe, Sienna, Brown, Gray and Black. These are the quiet ones. Match one to the wall and the keypad nearly disappears.
- Architectural metal (8). Bright Brass, Satin Brass, Antique Brass, Bright Chrome, Satin Chrome, Bright Nickel, Satin Nickel and Polished Graphite.
- Signature metal (2). Champagne and Graphite.
- Glass (2). Clear White Glass and Clear Black Glass.
The buttons always match the faceplate, so metal goes with metal and glass with glass. Antique Brass is finished by hand, so it varies a little from plate to plate. If nothing on the list works, Lutron makes a bespoke Palladiom keypad with an unfinished front plate that takes a custom metal finish, with white or black buttons.
Here's how we usually help people choose:
- Match the hardware, not the paint. If the door handles and faucets are satin nickel, a satin nickel keypad looks planned. Paint changes every few years. Hardware usually stays.
- Matte for walls you want quiet. In a white hallway, a white matte keypad is about the least visible thing you can put on the wall.
- Think about hands. Bright chrome and bright brass look great in a photo. Beside the door from the garage, where hands come in dirty, a satin finish is easier to keep clean.
- Hold a real sample. Lutron makes chip sets for these finishes, but even Lutron says chips aren't for exact matching. Look at one in the room's own light, morning and night.
Button count and layout
Each Palladiom column comes in four layouts: 2 buttons, 3 buttons, 4 buttons, or 3 buttons with a raise and lower bar. There are two shapes. The U.S. style is a tall rectangle that fits a standard wall box, the same kind your switches sit in now. The square style needs a square or round wall box that Lutron sells for it, and it can hold two columns, up to 8 buttons on one plate.
Our advice is fewer buttons than you think. Most rooms need three or four. This is how we decide:
- Count what you do in the room. If you can't name a button, you don't need it.
- Use raise and lower where people fiddle. In a family room or a bedroom, the bar lets you nudge a scene brighter or dimmer without picking a new one.
- Leave room to change your mind. Lutron lets a 4 button be swapped in the field for a 3 button with raise and lower. Other layout changes mean replacing the keypad base. If you're unsure about a room, start with one of those two.
- Gang with care. U.S. style Palladiom keypads can share a plate, up to four across, but only with other Palladiom pieces. Not beside a regular dimmer.
Engraving: keep it short
Every Palladiom keypad is engraved to order. Lutron's spec sheet says the engraving details have to be in at the time of purchase, and the order won't be processed until they are. So the words get decided before the keypad is ordered, not on install day. Palladiom supports a limited set of icons and languages, so if the family speaks French at home, we confirm the accented letters first.
The good news is that the buttons can be swapped in the field for a newly engraved set later. Nobody has to pull the keypad out of the wall.
These are the rules we follow when we write engraving with clients:
- One or two words. "Dinner" beats "Dining Room Dinner Scene". You're standing in the room. You know where you are.
- Say what happens, not which lights. Bright, Evening, Night, Off. Nobody wants to read "Pots and Island and Cove".
- Same words, same spot, every room. If Off is the bottom button in the kitchen, make it the bottom button everywhere. Muscle memory does the rest.
- Whole-house words only where they belong. Goodnight beside the bed. Away at the door to the garage.
Backlighting that doesn't keep you up
The engraving glows white, and the active scene shows as a brighter backlight. Lutron's Dynamic Backlighting Management adjusts the glow to the light in the room. It can also be programmed to change by time of day or by button press.
That matters in the bedroom. A keypad that glows like a night light gets covered with tape by the second week. We set bedroom keypads to drop way down at night.
Where keypads go in an Ottawa home
- Front entry. Arrival, Bright, Away, All Off. Away can shut off every light in the house and lower the shades on your way to the airport. It pairs well with the timed lighting in our arrival and away lighting post.
- Door from the garage. The door your family actually uses. Same buttons as the front entry, on the heated side.
- Kitchen. Cook, Dinner, Evening, Off. Pendants, pot lights and under-cabinet strips all set together.
- Family room. Watch, Relax, Bright, plus raise and lower. With Control4, Watch can also turn on the TV and lower the shades.
- Primary bedroom, both sides of the bed. Read, Night, Goodnight. Goodnight turns off the rest of the house and can leave a dim path to the ensuite.
- Top and bottom of the stairs. Two buttons is plenty. On and Off, or Night and Off.
If you have tunable fixtures like Ketra, one button can bring back the normal daytime light after a movie. Our circadian lighting post explains that side of it.
Turning a bank of switches into one keypad
This is where Palladiom earns its place. On HomeWorks, the lights don't need a switch at the wall. They can be wired back to Lutron dimming panels, usually in the mechanical room, and the keypads tell the panels what to do. That row of six switches by the patio door becomes one plate with four buttons. Our lighting control page shows what else the system can run.
It takes planning. The circuits have to come back to the panel, and every keypad needs its own low voltage cable. Easy before drywall, harder after. Our pre-wiring mistakes post covers what to get in while the walls are open.
Before any old switch comes out, we walk the room with you and write down what each one does today. More often than you'd think, one of them runs an outlet nobody remembers.
How keypads tie into Control4
Many of our clients pair Lutron with Control4. Control4 has drivers for both the HomeWorks QSX processor and RadioRA 3, and they include the keypad buttons. In practice that means a Palladiom button can do more than lights. Press Watch and Control4 can turn on the TV, pick the input and bring the shades down. Press Goodnight and it can lock the doors and arm the alarm while Lutron handles the lights.
It works the other way too. A Control4 schedule or the app can call up the Lutron scenes. Our smart home automation page shows the bigger picture.
Voice fits in here as well. Lutron makes Josh.ai ready wallplates in the Palladiom style. They put a Lutron keypad and a Josh Nano microphone side by side in the same wall box, with the keypad on the left or the right. Our Josh.ai post covers what Josh hears and what it keeps.
Questions to ask before you order
Go through these before anything gets ordered:
- Is the house on HomeWorks, RadioRA 3, or neither yet? That decides whether Palladiom is an option.
- U.S. style or square? Square needs its own wall box, and that has to go in before drywall.
- Which finish matches the door hardware in each room?
- How many buttons does each room really need, and can you name every one?
- Is the engraving final, and has everyone in the house read it?
- Which buttons should also run Control4 things like the TV, the shades or the alarm?
- Does every keypad location have a low voltage cable back to the system?
What it takes
On a new build or a gut renovation, we plan keypad locations from the drawings, the electrician runs the cable, and we program everything before you move in. Shades can go on the same keypads, and our Lutron motorized shading page shows those options. Palladiom shades are covered in our Palladiom shades post.
On a finished house it depends on the walls. Sometimes it's an existing box. Sometimes it's fishing new cable, which is slower on outside walls full of insulation. A site visit tells us which.
Talk to us about Palladiom
We're Ottawa's largest Control4 and Lutron dealer, and we design, install and support Lutron systems from Orléans to Kanata and across the river in Gatineau. Have a look at our Lutron lighting control page, then call us at (613) 830-6787 or send us a message. Send a photo of your worst bank of switches and the room it's in, and we'll tell you what a keypad there would look like. You can also drop by the showroom at 1344 Youville Drive in Orléans to talk it through.
Frequently Asked Questions
Can I get Palladiom keypads with Lutron RadioRA 3?
No. Lutron lists Palladiom keypads for HomeWorks, and the keypad is wired to a HomeWorks processor. RadioRA 3 uses Sunnata and seeTouch keypads. Sunnata is wireless and fits a standard wall box.
How many finishes do Palladiom keypads come in?
Lutron's spec sheet lists 22: ten architectural matte colours, eight architectural metals, two signature metals and two glass finishes. The buttons always match the faceplate. A bespoke version takes a custom metal finish.
Can I change the engraving later?
Yes. Engraving is ordered with the keypad, but the buttons can be swapped in the field for a newly engraved set without taking the keypad out of the wall.
Will a keypad light keep me awake?
It shouldn't. The white backlight adjusts to the light in the room on its own, and it can be programmed by time of day, so bedroom keypads can glow very low at night.
Can one keypad replace a bank of switches?
Yes, on HomeWorks. The lights are wired to dimming panels and the keypad sends commands, so one plate with a few scene buttons can replace a row of switches. It needs planning and a low voltage cable to each keypad.
Do Palladiom keypads work with Control4?
Yes. Control4 has drivers for Lutron HomeWorks QSX and RadioRA 3 that include keypad buttons, so one press can set the lights and also run the TV, the shades or the alarm.
