Blackout Shades for an Ottawa Home Theater: How to Stop the Light Leaks
A lot of the people who call us about a theater room already bought blackout shades. Then they fire up the projector on a Saturday afternoon and see a bright stripe down both sides of every window. The fabric is doing its job. The light is just going around it.
Blackout is a system, not a fabric. Below is what actually stops the light, based on Lutron's own installation guidance, plus the things that have to be decided before the drywall goes up.
Why a theater room needs real dark
A TV fights glare. A projector fights everything. The picture on a projection screen is light bouncing off a surface, so any daylight that lands on that screen turns the blacks grey. Dark scenes go muddy. A big TV copes better, but a bright window reflected in the screen still pulls your eye off the movie. If you're still deciding between the two, our projector vs TV post walks through it.
Ottawa adds its own twist. Around December 21 the noon sun only climbs about 21 degrees above the horizon here. In late June it gets up to about 68. That low winter sun comes straight through south and west windows and lands right where the TV hangs. So a room that looked fine when you moved in during July can be hard to watch on a January afternoon.
Where the light gets in
Picture a regular roller shade pulled all the way down. Light still has four ways in:
- Through the fabric. Sheer and light filtering fabrics are made to let light through. Only a blackout fabric stops it.
- Down the sides. Lutron's Roller 64 spec lists a 3/4 inch light gap on each side, between the fabric and the outside edge of the brackets. On tall, narrow shades Lutron may trim the fabric a bit more to keep it rolling straight, so the gap grows.
- Over the top. Light hits the roller and the ceiling above it, then bounces into the room.
- Under the bottom. Wherever the bottom bar doesn't meet the sill evenly.
Close one of those and the others suddenly look brighter. That's the whole game. Lutron's application note on light blocking puts the goal simply: block the direct path, and make any light that's left take a long, bent route into the room. It also says the only real way to judge the result is a mock-up on site. We agree. Every window and every wall is a little different.
The four parts of a real blackout roller shade
For maximum light blocking, Lutron recommends the same setup every time. Here's each piece and why it's there.
Blackout fabric
Lutron's fabric library at lutronfabrics.com lets you filter by openness, and blackout is its own category. Read the label carefully. Lutron's Roller 64 spec describes room darkening fabric as no view and maximum UV protection, then adds that complete blackout needs side channels plus a pocket or a fascia with a top back cover. Fabric is step one, not the finish line.
A pocket or fascia over the roller
The roller sits in a pocket recessed into the ceiling, or behind a fascia with a top back cover. Either one blocks the gap over the top. Lutron says the inside of the pocket should be a dark, non-reflective colour, and it offers a custom painted dark interior. A white pocket just bounces the light around and spills it into the room. Lutron also warns to check for anything that sticks out into the shade's path, like window locks and door handles.
Side channels
These are aluminum tracks that run up each side of the window. The edge of the fabric rides inside them, against black wool pile, so there's no straight path for light. Lutron recommends the 2.5 inch channel for every shade in a blackout room because it holds the fabric better against air pressure, and it's required on shades over 120 inches tall or 60 inches wide. Channels come in white, bronze and anodized, or a custom colour, and in custom lengths up to 150 inches. They can sit inside the window opening, on the wall just outside it, or be recessed into the jambs.
Alignment matters. The fabric drifts closer to the tube as the shade comes down, because the roll gets smaller. Lutron's advice is to line the channels up so the fabric is centred at the halfway point of its travel, and to expect a small adjustment after install.
A wool pile hembar and a sill angle
At the bottom, Lutron recommends a 1 inch exposed hembar with black wool pile. The pile also makes up for a sill or floor that isn't perfectly level. Add a sill angle under it, a small aluminum lip the bar closes against, and the light at the bottom has nowhere to go.
One catch. Lutron says not to use a sill angle at a point of egress, because it's a trip hazard. Lots of Ottawa theater rooms are in walkout basements with a patio door. On that door we rely on the hembar's wool pile and the shade pocket, and if the room has to be truly black, we add a drapery panel in front.
Why battery shades and Palladiom aren't the theater answer
We like battery shades a lot. Our Triathlon post explains why they're one of the best upgrades for an existing house. But Lutron doesn't offer side channels on battery-powered shades. Side channels are only for shades that run off a power supply, like Sivoia QS. So a battery shade in a theater will always show some light at the edges. Fine in a bedroom where room darkening is enough. Not great behind a projection screen.
Same story with Palladiom shades. They're made to be seen, with exposed brackets and no pocket. Lutron's note says Palladiom roller shades and Palladiom draperies aren't recommended where maximum light blocking is needed, because they can't be installed in a pocket or fascia.
A few more rules from the same note. Side channels and cable guides can't go on the same shade. Side channels don't work on shades sloped more than 5 degrees from vertical, so angled loft windows need another plan. And channels on a sheer fabric won't give you blackout. The fabric still lets light through.
Wired Sivoia QS shades: what the spec sheet says
For a theater we use hard-wired Sivoia QS roller shades. Here's what Lutron's Roller 64 spec sheet lists:
- Quiet. The motor is rated at no more than 35 dBA measured 3 feet away. In a quiet theater room, that matters.
- Speed. The bottom bar moves at 3.6 inches per second, so a 6 foot window closes in roughly 20 seconds.
- Shades stay lined up. Every shade in the room moves together and stays within 1/8 inch of the others, moving or stopped.
- Size. Standard Roller 64 shades go up to 8 feet wide, and the WIDR version up to 12 feet. Some fabrics limit the size.
- Wiring. Wired QS shades get low voltage power and communication on a single 4-wire cable. The QS Wireless version needs a 2-wire cable for power. Power comes from Lutron power supplies, either a plug-in unit or a 10-output panel.
- Memory. Shade programming isn't lost if the power goes out.
There's also a dual-mount bracket that holds two fabric rolls in the same window. Lutron says it's typically a sheer and a blackout. That's the setup we suggest when the family room doubles as the movie room. Sheer during the day so you keep the view of the yard, blackout when the lights go down.
Drapery in a theater room
Lutron is upfront about this. Drapery isn't as good at blocking light as a blackout roller, because it needs clearance to move. It can get much closer with the right details. Lutron supplies the track and motor, and the fabric comes from a drapery workroom, so the two have to plan together. Our guide to Lutron shades and drapery tracks covers the hardware. For light blocking, Lutron's note says:
- Use pleated drapery. Ripple fold and S-fold leave loops of fabric away from the track, and light comes through there.
- Mount the track well above the window, ideally more than 12 inches, close to the ceiling.
- For full blackout, hang the fabric 0 to 1/8 inch off the floor. Normally Lutron suggests 1/2 to 1 inch so it doesn't drag.
- Use a pocket closed on five sides, at least 12 inches tall inside. A ceiling-mounted track needs a pocket at least 5 inches wide. A wall bracket needs 6, and a double track with a sheer and a blackout needs 11.5.
- At the sides, use pockets or 12 inches of wall overlap, or fasten the fabric returns to the wall with hook-and-loop strips.
- On a centre-opening pair, order the extended overlap master carriers so the panels overlap more where they meet.
One button for movie night
Getting the room dark is half the job. The other half is not having to think about it. Lutron's shade spec lists Ethernet, RS232 and contact closure for tying the shades into A/V equipment and touch screens. For us that means Control4. Press Watch on the remote and the shades come down, the lights fade to a low step light and the projector warms up. Pause the movie and the lights come up just enough to find the snacks. Our one remote post shows how we set that up for the whole family.
The shades can also run on a schedule. Close the west windows on winter afternoons so the room is ready by the time the kids want to watch something, then open them in the morning.
What to sort out before drywall
A blackout theater is easy to plan and hard to fake later. Bring these to your builder or designer early:
- A low voltage cable from every window head back to where the shade power supplies will live.
- Ceiling pockets framed in and sized for the shade roll, with the inside painted matte black.
- Where the side channels go: inside the opening or on the wall outside it. That changes the trim detail around the window.
- Window hardware. Casement crank handles and patio door handles can get in the shade's way.
- Patio doors in the room, since they can't get a sill angle.
- Blocking in the ceiling for any drapery track.
Our pre-wiring mistakes post covers the rest of what should go in while the walls are open. Already finished the basement? A fascia with a top back cover and side channels screwed to the wall outside the window can be added to a finished room, and a plug-in power supply avoids opening walls when there's an outlet nearby. Our retrofit page explains how we work in finished homes.
Talk to us about your theater room
We're Ottawa's largest Control4 and Lutron dealer. We design home theaters and Lutron motorized shades together, so the screen, the speakers and the windows get planned as one room. Send us your window sizes and a couple of photos, even from your phone, and we'll tell you what it takes to get that room dark. Call us at (613) 830-6787 or send us a message. You can also drop by the showroom at 1344 Youville Drive in Orléans and see the shades move.
Frequently Asked Questions
Are blackout shades enough to make a theater room fully dark?
Not on their own. Blackout fabric stops light through the shade, but light still comes in around the edges. Lutron recommends a blackout roller shade in a pocket or a fascia with a top back cover, side channels, and a wool pile hembar with a sill angle.
Can battery-powered shades have side channels?
No. Lutron says side channels are not compatible with battery-powered shades. They are offered for shades powered by a power supply, like Sivoia QS, so a theater room usually gets wired shades.
How loud are motorized shades in a home theater?
Lutron rates the Sivoia QS Roller 64 drive at no more than 35 dBA measured 3 feet from the motor, with smooth starts and stops.
Can I have a sheer and a blackout shade on the same window?
Yes. Lutron makes a dual-mount bracket that holds two fabric rolls in one window, typically a sheer for daytime and a blackout for movies.
Do Lutron shades work with Control4?
Yes. Lutron shade systems can tie into A/V and control systems, and we program them in Control4 so one button lowers the shades and dims the lights.
Can blackout shades be added to a finished basement theater?
Usually, yes. A fascia with a top back cover and side channels mounted on the wall can go into a finished room, and a plug-in power supply helps when there's an outlet nearby. Patio doors can't get a sill angle, since Lutron says not to use one at a point of egress.
